跳至主要内容

Induction Furnace Repair Services

Induction Furnace Repair Services


Induction Furnace Repair Services

Energy-saving intermediate frequency furnace - matters needing attention in maintenance

In induction furnace repair services, the energy-saving intermediate frequency furnace needs attention not only before the furnace is turned on, after the furnace is turned on, but also during maintenance.

The intermediate frequency induction furnace should check the electrical equipment, cooling water system, induction switch air conditioning copper pipe, etc. before starting the furnace.

After the furnace is turned on, when discharging, it is necessary to check the scraps returned to the furnace to prevent infiltration of inflammable and explosive materials and other hazardous materials.

When maintaining the energy-saving intermediate frequency furnace, the high-frequency generator room should be kept clean, and the accumulation of flammable and explosive materials should be prohibited.

After the energy-saving intermediate frequency furnace is ignited, when discharging the material, it is necessary to check the scraps returned to the furnace to prevent the infiltration of inflammable and explosive materials and other hazardous materials.

In order to avoid the occurrence of capping, it is forbidden to add cold material and wet material directly during the desolventization, and it is not allowed to add a large block surface layer after the molten liquid is filled to the upper end.

In order to prevent accidents caused by the explosion of the energy-saving intermediate frequency furnace, the pouring site and the bottom pit in front of the furnace have no water storage and no obstacles;

When pouring, two people should cooperate with each other, and the remaining desolvation can only be poured at the designated place, and it cannot be stolen everywhere.

Hani Metallurgy is a high-tech enterprise specializing in intermediate frequency induction furnaces. For specific energy-saving intermediate frequency furnace wholesales, please consult Hani Metallurgy electric furnace related technical sales personnel.


Hani Metallurgy is the one-stop supplier able to design, manufacture, install, and commission your melt shop and hot rolling mill plant from A to Z.


Free send inquiries to stella@hanrm.com  or inquiry99@hanmetallurgy.com if any needs.

Email: stella@hanrm.com Or stellarollingmill@gmail.com                              inquiry99@hanmetallurgy.com

Whatsapp/Wechat:+8615877652925

Website:  https://www.hanmetallurgy.com

标签：
地点: W8MX+8C 土库曼斯坦阿什哈巴德

评论

发表评论

此博客中的热门博文

Application Range of Medium Frequency Induction Furnace

  Application Range of Medium Frequency Induction Furnace (1) Intermediate frequency induction furnace is used for forging and rolling 1. Wheel forgings, ring forgings, shaft forgings, cylinder forgings, gear forgings, stainless steel forgings, and large flanges. 2. Hot heading of standard parts and fasteners, such as heating for tempering, forging, and extrusion of high tools. 4. Quenching and tempering of bar materials (2) Intermediate frequency induction furnaces are used for smelting 　 Including the smelting of steel, gold, silver, copper, and aluminum, especially in the foundry industry (3) Intermediate frequency induction furnace is used for heat treatment 1. Heat treatment of various hardware tools and hand tools. Such as pliers, wrenches, screwdrivers, hammers, axes, etc. 2. High-frequency hardened crank pins, sprockets, camshafts, valves, various rocker arms, rocker shafts for various auto parts and motorcycle parts; various gears, spline shafts, transmission axles, High-frequ
发表评论
阅读全文

Troubleshooting of Medium Frequency Furnace

Troubleshooting of Medium Frequency Furnace This article introduces the faults and solutions of medium frequency furnace. 1. Fault phenomenon: large DC current, low DC voltage, and if the voltage, dull equipment sound, over-current protection. Analysis and treatment: the thyristor with one arm of the inverter bridge may be short-circuited or open-circuited, resulting in the operation of the three-arm inverter bridge. Use an oscilloscope to observe the voltage drop waveform of the thyristor on the four bridge arms of the inverter bridge. If the voltage drop waveform of the thyristor on one bridge arm is a line, the thyristor has been through; if it is a sine wave, the thyristor has not been through. Replace the through thyristor; find out the reason why the thyristor is not turned on. 2. Fault phenomenon: when the heavy load cold furnace is started, all electrical parameters and sounds are normal, but the power cannot be raised, and overcurrent protection. Analysis and
发表评论
阅读全文

Advantages and Disadvantages of Electric Arc Furnace and Induction Furnace Steelmaking

Electric Arc Furnace VS Induction Furnace Steelmaking Comparison of advantages and disadvantages of electric arc furnace and induction  furnace steelmaking 1. The induction furnace heats up quickly and has high thermal efficiency. The heat is generated inside the charge (steel liquid), so the heating is fast. In the arc furnace, the heat of the arc after the material is cleared must be transferred to the molten steel through the slag, which is indirect heating. Thermal efficiency is poor. The furnace is in the shape of a basin, and a large part of the heat of the arc is lost through the furnace cover and the furnace wall. 2. The oxidative burning loss of elements in induction furnace steelmaking is less. Because there is no ultra-high temperature action of the arc in the induction furnace steelmaking, the burning rate of the elements in the steel is low. 3. In the induction furnace steelmaking, the composition and temperature of the molten steel are relatively uniform.
发表评论
阅读全文