跳至主要内容

100 kg Induction Furnace for Sale

100 kg Induction Furnace for Sale


100 kg Induction Furnace for Sale

Series line constant power (energy-saving 100kg induction furnace for sale)


The constant power (series energy-saving type) 100 kg induction furnace was launched for sale. After a long-term production practice tests, it has been widely praised by users. Now it has been improved on the original basis to make its performance more excellent.


<1> High melting rate. During the melting process, the power can be kept running in the best frequency band, which greatly eliminates the adverse effect of the new lining on the melting speed.


〈2〉The quality of molten steel is high, and the yield of castings is high.


<3> High power factor. During the operation of the whole machine, the power factor can reach more than 0.97.


<4> No interference to the power grid.


<5> Low power consumption, more than 10% power saving.


<6> The success rate of starting is high, and the success rate of starting is 100% under any load.


<7>The main control board adopts a connector interface, which is more convenient for maintenance.


<8> The inverter uses series thyristors to minimize the damage rate of thyristors.


Series inverter circuit


The series inverter power supply put into the market is a high-efficiency frequency conversion device, which is suitable for heating, diathermy, surface annealing, quenching, pipe bending, smelting, etc. Its advantages are:


<1> The current flowing through the inductor in the series inverter circuit is close to the active current, so the DC current is small and the loss is small.


<2>Easy to start, simple and reliable, suitable for frequent starting occasions.


<3>The current naturally crosses zero and is easy to shut down, so the operating frequency is higher.


Technical Parameter of 100 kg Induction Furnace for Sale

SN
Name
Unit
GW-0.05
GW-0.1
GW-0.15
GW-0.20
1
Electric Furnace Rated Capacity
Kilogram
50
100
150
200
2
Rated power of intermediate frequency power supply
kilowatt
80
100
120
160
3
Incoming line voltage of intermediate frequency power supply
Volt
380
380
380
380
4
Melting furnace frequency
Hertz
1000

5
Melting rate
Ton/hour
0.04
0.1
0.13
0.16
6
Power consumption (stainless steel)
Degree/ton
720
700
700
680
7
Power consumption (cast iron and carbon steel)
Degree/ton
650
640
620
600
8
Complete equipment water consumption
Ton/hour
7
7
7
7
9
Melting time
Minute
30
30
30
30
10
Induction coil rated voltage
Volt
1000
1000
1000
1000
11
Furnace rated temperature
°C
1600
1600
1600
1600
12
Transformer rated capacity
KVA
100
100
160
200

Hani Metallurgy is the one-stop supplier able to design, manufacture, install, and commission your melt shop and hot rolling mill plant from A to Z.


Free send inquiries to stella@hanrm.com  or inquiry99@hanmetallurgy.com if any needs.

Email: stella@hanrm.com Or stellarollingmill@gmail.com                              inquiry99@hanmetallurgy.com

Whatsapp/Wechat:+8615877652925

Website:  https://www.hanmetallurgy.com

标签：
地点: Mimar Sinan, 129/1. Sk. No:8, 06670 Çankaya/Ankara, 土耳其

评论

发表评论

此博客中的热门博文

Application Range of Medium Frequency Induction Furnace

  Application Range of Medium Frequency Induction Furnace (1) Intermediate frequency induction furnace is used for forging and rolling 1. Wheel forgings, ring forgings, shaft forgings, cylinder forgings, gear forgings, stainless steel forgings, and large flanges. 2. Hot heading of standard parts and fasteners, such as heating for tempering, forging, and extrusion of high tools. 4. Quenching and tempering of bar materials (2) Intermediate frequency induction furnaces are used for smelting 　 Including the smelting of steel, gold, silver, copper, and aluminum, especially in the foundry industry (3) Intermediate frequency induction furnace is used for heat treatment 1. Heat treatment of various hardware tools and hand tools. Such as pliers, wrenches, screwdrivers, hammers, axes, etc. 2. High-frequency hardened crank pins, sprockets, camshafts, valves, various rocker arms, rocker shafts for various auto parts and motorcycle parts; various gears, spline shafts, transmission axles, High-frequ
发表评论
阅读全文

Troubleshooting of Medium Frequency Furnace

Troubleshooting of Medium Frequency Furnace This article introduces the faults and solutions of medium frequency furnace. 1. Fault phenomenon: large DC current, low DC voltage, and if the voltage, dull equipment sound, over-current protection. Analysis and treatment: the thyristor with one arm of the inverter bridge may be short-circuited or open-circuited, resulting in the operation of the three-arm inverter bridge. Use an oscilloscope to observe the voltage drop waveform of the thyristor on the four bridge arms of the inverter bridge. If the voltage drop waveform of the thyristor on one bridge arm is a line, the thyristor has been through; if it is a sine wave, the thyristor has not been through. Replace the through thyristor; find out the reason why the thyristor is not turned on. 2. Fault phenomenon: when the heavy load cold furnace is started, all electrical parameters and sounds are normal, but the power cannot be raised, and overcurrent protection. Analysis and
发表评论
阅读全文

Advantages and Disadvantages of Electric Arc Furnace and Induction Furnace Steelmaking

Electric Arc Furnace VS Induction Furnace Steelmaking Comparison of advantages and disadvantages of electric arc furnace and induction  furnace steelmaking 1. The induction furnace heats up quickly and has high thermal efficiency. The heat is generated inside the charge (steel liquid), so the heating is fast. In the arc furnace, the heat of the arc after the material is cleared must be transferred to the molten steel through the slag, which is indirect heating. Thermal efficiency is poor. The furnace is in the shape of a basin, and a large part of the heat of the arc is lost through the furnace cover and the furnace wall. 2. The oxidative burning loss of elements in induction furnace steelmaking is less. Because there is no ultra-high temperature action of the arc in the induction furnace steelmaking, the burning rate of the elements in the steel is low. 3. In the induction furnace steelmaking, the composition and temperature of the molten steel are relatively uniform.
发表评论
阅读全文